Laura M56 Parts

updated 2021-09

Contents:
1. M56 Versions
2. M56 Parts
3. M56 Parts Info
4. M56 Tools

 

 

 


1. M56 Versions

Three power and speed versions were made for Batavus USA models. 1.0 horsepower, 1.5 and 2.0. Each USA state required a different version.

Only four things are different between the speed versions. Everything else is the same.

 1.0 hp 00 1.5 hp 00 2.0 hp
20 mph
    25 mph    30 mph    ##  parts that are different
———————————————————————————
560194    560180    560180 #189  crankcase 40km or 50km
540681    540681    540695 00#6  cyl. head lo or hi comp
560194    560180    560180 00#7  cylinder 40km or 50km
561787    561782    561782 #116  carburetor H9 or H12

 

 


1. Parts for Laura M56 Engine

Trac (M56) Parts

Batavus Regency (M56) PartsThe parts list below is made from the Batavus USA Spare Parts Catalog for 1978-80 Regency VA and Regency HS (20, 25, 30 mph). Combined with that are parts from the Trac USA Parts List for 1982-86 Clipper, Eagle and Hawk (25 and 30 mph).

In 1978-80 the M56 engine was made by Laura in Holland, mostly for Batavus mopeds. It was remade in 1982-85 by Daelim in Korea, mostly for Trac mopeds. The Trac remake is 90% the same. Only some pulley, pedal and drive shaft parts are different, shown below in a lighter color shade.

Price color: new  used   Part color: 25,30mph  20mph

 

Laura M56 parts on ’78-80 Batavus and ’82-86 Trac mopeds

 #  Batavus  Trac xx Price (each)
 xx  number  no.  qty xxx  Description
===============================
001 827600 04060 4 $0.30 nut M6
002 846600 06060 4 $0.25 lock washer M6
003 847600 05060 4 $0.20 washer M6
004 829682 10025 4 $4.50 cylinder stud M6x107
005 481883 80015 1 $5.00 spark plug NGK BR6HS
006 540681 00000none  cylinder head (20 mph)
006 540681 80001 1 none  cylinder head (25 mph)

006 540695 80010 1 $40.0 cylinder head (30 mph)
007 560688 00000 1 none  cylinder 25km (20 mph)
007 540680 80003 1 none  cylinder 50km (25 mph)
007 560685 80003 1 none  cylinder 50km (30 mph)
008 490682 80029 1 $6.00 cylinder base gasket
009 540580 80016 1 none  piston Ø39.96 18-12-14
009 540580 80017 1 none  piston Ø39.97 18-12-14
009 540580 80018 1 none  piston Ø39.98 18-12-14
009 540580 80019 1 none  piston Ø39.99 18-12-14
009 540580 80020 1 none  piston Ø40.00 18-12-14
009 540580 80020 1 none  see pistons for
substitutes 

010 561895 82013 1 $3.00 plug wire rubber boot
011 480502 80021 2 $10.0 piston ring Ø40 x 1.5 FG
012 480501 80022 1 $10.0 piston pin Ø12.0 x 33
013 841520 80023 2 $1.50 piston pin clip Ø12
014 480325 80024 1 $10.0 piston bushing Ø11.8 x 14 x 11
015 560381 80025 1 $100  crankshaft good-used or $150 new
016 810080 10034 2 $10.0 bearing 6202 C3
017 830000 80026 1 $1.50 clutch hub key 3 x 5 M-86
018 830001 80027 1 $2.00 flywheel key 2 x 3.7 M-81
019 540882 81001 1 20-30 clutch saucer
020 560395 81002 1 $1.00 wave washer 15x24x1
021 490390 81003 1 $7-11 disk nut M15-1.0
022 540886 81004 1 25-40 weight-spring
023 540803 81005 1 15-25 clutch hub
024 540898 81006 1 22-10metal plate
025 480889 81007 1 $32.0 friction plate
026 540899 81008 1 $5-8  star spring
027 480890 81009 1 7 –12 outer locking plate
028 820509 81010 6 $0.50 hex bolt M5x20
029 540809 81011 1 $25.0 friction lining ring, this can reduce slipping
030 560890 810??  1 50-80 clutch housing
031 813090 81013 2 $10.0 bearing 12x18x10 HK1210
 or $13 for 12x18x20 HK1220
032 490813 00000none  shim as needed 12x24x0.8
032 490814 81014 1 $4.00  shim as needed 12x24x0.5 same as M48 one 480899
033 841505 81015 1 $1.00 circlip Ø10.9 12.0 shaft
034 560892 81016 1 $30.0 start plate with a 1/2 worn button
035 480892 81018 1 $8.00 leaf spring
036 829605 80047 1 $5.00 starter stud M6 x 55
037 490293 81019 1 none  cover support plate
038 561096 00000 1 $15.0 sprocket 13T (20 mph)
038 561097 81037 1 $15.0 sprocket 17T (25 & 30)
039 490886 81020 1 $6.00 starter mount spring
040 490980 81021 1 $12.0 starter arm lever
041 827610 04060 2 $0.30 nut for starter M6
042 836103 81012 3 none  rivet for lining ring 3×6
043 843500 06050 6 $1.00 wave washer M5 thin
044 490835 none   1 $6.00 starter cable spring
045 813088 81028 1 $15.0 needle bearing 12x15x10 inner, 1 end open BK1210
046 560883 81023 1 $20.0 clutch hub Ø21 at seal
047 561385 00000none  pulley shaft Batavus Ø15
T47 000000 81030 1 $45.0 pulley shaft Trac Ø12
048 561590 00000 1 $57.0 62T pulley Ø15 center
T48 000000 81026 1 $40.0 62T pulley Ø12 center
049 830004 81031 1 $3.00 shaft key 3 x 6.5 M-88
050 560891 81025 1 none  toothed belt T5x395-20, 79 teeth note 1
050 560891 81025 1 $18.0 toothed belt T5x390-20, 78 teeth note 1

051 810182 10028 1 $8.00 bearing 17x40x12 6203
052 490813 81029 2 $4.00 pulley shaft shim 12x24x 0.8 same as M48 one 480899a
054 840011 81038 1 $5.00 tab washer Ø17 x 32
055 828200 81039 1 none  sprocket nut M12-1.25
056 561098 00000none  drive shaft Batavus
T56 000000 81033 1 none  drive shaft Trac
057 541685 80030 1 $15.0 exhaust clamp
058 846600 06060 1 $0.20 lock washer M6
059 820635 25614 1 $0.40 hex bolt M6x25
063 491088 00000 1 $5.00 shim washer 10 x 24 x 0.8
T63 000000 81034 1 none  shim washer 17 x 24 x 0.8
T63 491088 81034 1 $5.00 substitute 17 x 24 x 1.0

065 561082 00000none  ratchet wheel M20-1.0
T65 000000 81036 1 $45.0 ratchet wheel M20-1.0
067 491086 81035 1 $8.00 shim 20 x 31
069 816282 81044 1 $15.0 drive shaft R seal 20x26x4
070 491087 81041 1 none  plate
071 561092 81040 1 none  pedal sprocket 12T M20-1.0
075 561789 80031 1 $7.00 air box front bracket
076 490181 80032 1 $7.00 case gasket
077 490189 80033 2 $5.00 centering bush Ø8×12
078 490186 10017 1 $5.00 oil fill and check plug
079 560185 80034 1 none  grommet for magneto wires
080 823505 80048 8 $1.00 case screw slot M5x35
081 816187 81042 1 $9.00 left crank seal 15x32x7
082 816384 81043 1 $8.00 right crank seal 21x32x7
083 816186 81045 1 $6.00 pulley shaft seal 15x30x5
084 816284 81046 1 $7.50 drive shaft L seal 17x35x7
085 820675 80045 1 $1.00 carb hex bolt M6 x 75
086 829606 80047 1 $6.00 carb stud  M6 x 50
087 481784 80035 1 $4.00 reed valve gasket square
088 481783 80036 1 $49.0 reed valve 4-petal
089 829510 80046 1 $6.00 R cover stud M5 x 75
090 820501 00512 1 $0.40 hex bolt M5 x 12
091 847520 05050 1 $0.20 plain washer M5
092 560292 80037 1 $7.00 left cover bracket
093 561885 82000 1 $210  magneto good-used 0212-010-004
095 481890 82015 1 $6.00 spark plug cap
116 561782 82500 1 $220  carburetor H12 (25,30)
116 561787 00000 none  carburetor H8 (20 mph)
140 491797 82522 1 $6.00 reed valve gasket round
141 491796 82523 1 $23.0 insulator block (not shown)
142 491795 80038 1 $1.00 fiber washer M6
143 843600 05060 1 $0.20 plain washer M6
148 560213 80042 1 25-40 left cover (magneto)
149 560210 80041 1 $39.0right cover (clutch) used
150 560291 80044 1 $7.00 slot step-cap nut rear M5
151 560290 80043 2 $7.00 slot step-cap nut front M6
153 823435 80049 2 $1.00 pan phillips screw M4x35
154 491387 00000 1 $13.0 stepped ring 15 x 24 x 4.6
155 491386 00000 1 $2.00 wire clip Ø15 shaft x 1
156 848015 00000 1 $2.00 washer 15.3 x 27.7 x 2.4
157 848012 05100 1 $0.50 washer M10
158 847000 06100 1 $0.50 lock washer M10
159 828000 81027 1 $2.00 nut M10-1.0
165 561388 00000 1 $7.00 washer 15.5×23.8×1.0
T165 00000 81032 1 none  saucer spring 12.2×22.8×1
T165 00000 81032 1 $7.00 substitute 12.2×24.8×0.9
166 823512 80050 1 $0.70 wide pan slot screw M5x12
169 540692 80028 1 $9.00 head gasket
175 561788 00000 1 $9.00 air filter bracket Batavus
175 000000 80039 1 $9.00 bracket Trac w/threads for #C
189 560194 00000 none  L & R engine case (20 mph)
189 560180 80040 1 $55.0 L & R engine case (25, 30)
194 820308 81017 2 $1.00 phillips screw M3x10
195 810080 10034 1 $10.0 bearing 15x35x11 6202
000  45.228 84047 1 $7.00 starter chain 3/8 x 5/32 x 32L
000 not quite #35. 35 fits, but can lift off the sprocket 
000  45.234
00000 1 $3.00 starter chain master link #35

Pedal chain tensioner only on Trac models:
A. 84048 $4.00 starter spring x
B. 84049 $6.00 starter guide x.
C. 84050 $5.00 starter bolt xxx
D. 84051 $1.50 washer Ø9×1.0 (2)

 

 

 

Note 1: The original belt T5X395 with 79 teeth was unavailable for many years from about 1990 to 2020. During that time the only belt available was one tooth (5 mm) shorter T5X390, sold online by Get-to-It Sales. The shorter belt was too tight unless the rear pulley teeth were shaved down. Many M56 rear pulleys have had their teeth shaved. With shaved teeth the shorter belt fits but the original belt is too loose.


To get a correct fitting belt, here is how to tell if the tops of the teeth have been shaved off. Original uses T5X395. Shaved uses T5X390. This is important because there is no way to adjust the belt tension, and no automatic belt tensioner.

 

 

 

 


2. M56 Parts Information

More to come…

 


3. M56 Tools

More to come…