Contents:
1 a. ’79-81 Yamaha QT50 VM12-SC-3L5
b. ’82-87 Yamaha QT50 VM12-SC-4L4
c. ’83-02 Yamaha PW50 VM12-SC-4X4
d. ’03-06 Yamaha PW50 VM12-SC-5PG
2 a. ’83-90 Trac (Daelim) VM13-SC-R4
b. ’78-81 Indian AMI50 VM10-SC-H9
3. ’76-83 Angel (TYM) VM10-24
4. Other Carbs like Mikuni
5. Mikuni Jets
6. Info
7. Tillotson Carb on Indian AMI-50
These are the baby Mikuni’s, the smallest of the small, 10 to 13mm for limited 50cc engines. See Info below.
1. Mikuni VM12SC on Yamaha QT50, PW50
Mikuni VM12SC is a 12mm carburetor (12mm venturi diameter) with an 18mm clamp diameter. It is not like any common Mikuni for a limited 50cc, like a moped or a kids off road. Apparently, Mikuni made carbs according to to each big manufacturer’s design. So Kawasaki KDX50, Suzuki JR50 have baby Mikuni carbs but with different designs than Yamaha PW50 and QT50.
VM12SC versions: The first version was 3L5 on 1979-81 QT50. It had an idle air screw just to the left of the idle speed screw. After 1981, on versions 4L4, 4X4, 5PG the air screw was to the right of the idle speed screw. The off road 4X4 and 5PG versions were mostly the same except the cables exited at 90 degrees, with metal curved pipes, instead of straight up.
1. 1979-81 Yamaha QT50, 3L5-00 with #75 jet, 3L5-01 with #70 jet
2. 1982-87 Yamaha QT50, 4L4-00 with #70 jet
3. 1983-02 Yamaha PW50, 4X4-00 with #70 jet
3. 2003-06 Yamaha PW50, 5PG-00 with #70 jet
Parts List A is ’79-81 QT50, B is ’82-87 QT50,
. quantities C is ’83-02 PW50, D is ’03-06 PW50
#0ABCD price Yamaha # description
1 1000 none 3L5-14101-01 carburetor ’79-81 QT50
1 0100 none 4L4-14101-00 carburetor ’82-87 QT50
1 0010 none 4X4-14101-00 carburetor ’83-02 PW50
1 0001 none 5PG-14101-00 carburetor ’03-06 PW50
2 1111 none 3L5-14181-07 float bowl
3 1111 none 3L5-14184-00 float bowl gasket
4 1111 $8.00 620-14231-14 main jet 70 M5-0.75 large round
5 1100 none 3L7-14141-10 needle jet E0 Ø2.05
5 0011 none 3L7-14141-12 needle jet
6 1111 $0.00 3L5-14142-40 idle jet 40 M4-0.7 thread
7 4444 $0.70 98580-04014 float bowl screw M4 x 14 phillips
8 1111 none 3L5-14198-00 top gasket
9 1100 none 3L5-14158-00 carb top cap
10 2200 $5.00 12G-14106-00 cable adjuster-stop M6-0.75
11 2211 $2.50 802-14161-00 adjuster lock nut M6-0.75 x 3 hex9
12 2200 $2.00 8A7-14169-10 cable rubber cap
13 1111 none 3L6-14185-01 float (not Trac, 90 deg different)
14 1111 N/A 3L5-14190-00 float needle = Trac 10206
15 1111 $4.00 603-14186-00 hinge pin Ø2 x 16
16 1100 none 3L5-14112-25 throttle slide
16 0011 none 3L5-14112-40 throttle slide
17 1111 $5.00 3L5-14137-00 spring stop “M” clip
18 1111 none 3L6-14116-06 jet needle 3X1 Ø2.0 Ø1.36 x 30.7
18 1111 none 36R-1490J-06 jet needle set 17, 18, 20 3X1
19 1111 $9.00 174-14131-01 throttle spring Ø10.5 x 52
20 1111 $2.00 127-14137-00 jet needle clip Ø2.0
21 1111 $0.00 3L6-14133-00 idle speed screw spring
22 1111 $0.00 36R-14103-00 idle speed adjust screw
23 1111 $0.00 58E-14171-00 choke plunger
24 1111 $0.00 127-14135-00 choke spring
25 1111 $0.60 98580-05012 top cover screw M5 x 12 phillips
26 1111 $0.25 92990-05100 top screw washer M5 spring type
27 1000 $0.00 3L5-14123-01 early idle air mixture screw (’79-81)
28 1000 $0.00 3L5-14962-00 early idle air screw washer (81 only?)
29 1111 $1.50 95380-05600 clamp nut M5 x 5 hex9
30 1111 $0.70 98517-05030 clamp bolt M5 x 30 pan phillips
31 1111 $0.00 90445-05N13 drain hose 200mm
32 2222 $5.00 3F7-14134-00 air and drain screw spring Ø4.8 x 10
33 1222 $6.00 36R-14104-00 air and drain screw M6-0.75×20
34 1111 none 1M3-14997-00 clamp seal Ø23
35 1111 none 1V3-14271-00 clamp sleeve Ø18 x Ø23 slotted
36 0011 none not sold 0000 top cover with curved pipes
39 0022 $2.50 17L-14106-00 cable adjuster nut M6-0.75×3 hex9
40 0022 17L-14106-00 cable adjuster
41 0022 $0.00 180-14169-00 cable rubber cap
41 0022 $3.00 WPS-70-1028 rubber cap similar, newer style
2. Mikuni H9-10 on Indian, R4-13 on Trac (Daelim)
H9 is a 10mm carb with a 18mm clamp diameter. R4 is a 13mm carb with a 20mm clamp diameter. They look almost the same, and share many parts in common.
1. ’78-81 Indian AMI-50 (some), 2. ’84-90 Trac mopeds with Daelim engine
Parts List L is Trac Liberty, Escot, Image O is Trac Olympic
. quantities C is Trac Clipper, Hawk, Sprint I is Indian AMI50
# LOCI price Trac# new# Indian# description
00 1100 none 12201 13201 E000-00-00 carburetor Trac Liberty R4-13
01 0010 none 00000 13202 E000-00-00 carburetor Trac Clipper R4-13D
01 0001 none 00000 00000 E210-30-50 carburetor Indian AMI50 H9-10
01 1110 $75.0 12201 13201 E000-00-00 carburetor body bare Trac
01 0001 none 00000 00000 E210-30-50 carburetor body bare Indian
02 1101 none 12211 13215 E237-70-50 needle jet E8 Ø2.05
02 0010 none 00000 13216 E000-00-00 needle jet D8 Ø2.10
03 1111 N/A 10206 00000 E238-80-50 float needle Yamaha 3L5-14190-01
04 1110 $0.00 10201 00000 E000-00-00 idle jet 40, thread M4-0.7
04 0001 none 00000 00000 no number idle jet not-replaceable, tight press
05 0000 --N/A-
00000 00000 E236-00-50 main jet 60, M5-0.75 small round
05 0001 $8.00 00000 00000 E236-25-50 main jet 62.5 use Dellorto #60
05 1100 --N/A- 12205 13206 E000-00-00 main jet 65 use Dellorto 1486 #62
05 0010 --N/A- 00000 13207 E000-00-00 main jet 70 use Dellorto 1486 #68
06 1111 none 12218 13223 E238-10-50 float white-clear plastic (not QT50)
07 1111 $4.00 10207 00000 E238-07-50 float hinge pin Ø2 x 16
08 1111 none 12203 13204 E238-00-50 float bowl gasket
09 1110 none 12204 13205 E000-00-00 float bowl no vent
09 0001 none 00000 00000 E238-30-50 float bowl w/vent
10 2222 $0.70 10202 00000 E237-06-50 float bowl screw M4 x 14 phillips
11 1111 $0.60 12217 13222 E238-12-50 top cover screw M4 x 25 phillips
12 2222 none 10203 00000 E237-01-50 rubber cap original short
12 2222 $3.00 10203 00000 E237-01-50 rubber cap substitute 70-10228c
14 0001 none 00000 00000 E237-02-50 top cover, smooth cable holes
15 1111 none 12213 13218 E237-04-50 top gasket
16 1111 $9.00 10204 00000 E238-16-50 throttle spring Ø10.5 x 52
17 1111 $6.00 12207 13209 E237-11-50 spring plate (can use “M” clip)
18 1000 $0.00 12210 00000 E000-00-00 jet needle 3J2-3 Ø2.0
18 0100 $0.00 00000 13213 E000-00-00 jet needle 3X6-4 Ø2.0
18 0010 $0.00 00000 13214 E000-00-00 jet needle 3T6-4 Ø2.0 Ø1.45 x 31.9
18 0001 $0.00 00000 00000 E237-08-50 jet needle 3G1-6 Ø2.0 Ø1.40 x 34.4
19 1111 $2.00 12206 13208 E237-12-50 needle clip Ø2.0
20 1101 none 12216 00000 E238-14-50 throttle slide Ø14 x 20, says 2.0
20 0010 none 00000 13221 E000-00-00 throttle slide Ø14 x 20, says 4.0
21 1111 $1.50 12213 13218 E237-04-50 clamp nut M5 x 4 hex9
22 1111 $5.00 12220 13225 E238-02-50 choke spring Ø6 x 19
23 1111 $14.0 12219 13224 E238-06-50 choke plunger Ø8 x 20
24 1111 $0.60 12212 13217 E237-05-50 clamp screw M5 x 25 phillips
25 1111 $9.00 12208 13210 E237-10-50 idle spd screw M6-0.75×17 short tip
26 2222 $5.00 12209 13211 E237-09-50 idle screw spring Ø4.8 x 10 (used 9)
27 1111 $6.00 10205 00000 E238-18-50 idle air screw M6-0.75×20, long tip
28 2220 none 10208 00000 E000-00-00 cable rubber boot original
28 2220 $2.00 10208 00000 E000-00-00 cable rubber boot substitute 1476-06
29 2220 $5.00 10209 00000 E000-00-00 adjuster M6-0.75 female x 16 hex7
30 1110 $19.0 12215 13220 E000-00-00 top cover, threaded cable holes
31 4440 $3.00 10210 00000 E000-00-00 adjuster lock nut M6-0.75 x 2 hex7
32 2220 $0.00 12222 13227 E000-00-00 cable curved pipe M6-0.75
33 0001 none 00000 00000 E000-00-00 clamp sleeve Ø18 x Ø23
33 1110 none 00000 00000 E000-00-00 clamp sleeve Ø20 x Ø23
1. Mikuni cable rubbers, 2. Indian Mikuni idle hole before and after drilling
Indian Mikuni carb service
The idle hole is often blocked. There are three spray holes, the main and mid-range under the throttle slide, and the smaller idle hole downstream of the throttle slide. When the bike is idling the slide is down and only the idle hole is active. A small slit of air under the slide blows over it, creating the suction and breaking up the liquid gasoline into small droplets. The drill size is tiny, a #76 which is 0.020 inch. The drill is held in a pin vise. The pin vise goes into the drill chuck. After about 2mm of depth there is a empty chamber behind the hole. That chamber leads to the idle jet which is at the top of a vertical tunnel-tube made into the zinc casting. The idle jet can be cleaned separately from below. It is smaller, like maybe 0.010 inch. That is smaller than the smallest drill #80 in a numbered set.
Carb spray is used to tell if the idle hole or idle jet is clogged. When sprayed up from the vertical idle tunnel-tube, the spray should shoot out from the mid range hole and dribble out from the idle hole.
3. Mikuni VM10-24 on Angel (TYM) mopeds
This carb is on Taiwan-made Angel and Speed Bird mopeds. It is a 10mm carburetor with a 20mm clamp diameter.
It is a 1960’s to early 70’s design, like a 1965 Yamaha U5 Newport, or a 1970 Suzuki F50 Cutlass carburetor. It has a brass swinging twin-float and a replaceable float needle seat. It has nothing made of rubber in it, unlike more modern carburetors.
1. ’77 Angel AP48, 2. ’83 Angel BP48-S, 3. ’79 Angel BP48-S, 4. ’77 Speed Bird BP48
# Angel part# Trac# price description
0 786-01-31000 00000 none carburetor assy
1 786-01-3100a 00000 $0.00 carburetor body bare
2 786-01-31510 00000 $0.00 cable rubber boot
3 786-01-3110a 00000 $23.0 carb top M20-1.0 thread
4 786-01-31440 00000 none throttle spring Ø13 x 38 stiff original
4 786-01-3144a 00000 $6.00 throttle spring Ø13 x 50 soft substitute
5 786-01-31380 00000 none spring plate Ø13-2.5 use W clip
5 786-01-3138a 00000 $5.00 plate substitute W clip
6 786-01-31340 13208 $2.00 needle clip Ø2.0
7 786-01-31330 00000 $15.0 jet needle 3G9 Ø2.00 Ø1.60 x 34.4
8 786-01-31470 00000 $45.0 throttle slide Ø16 x 23.5, says 2.0
9 786-01-3120a 00000 $5.00 cable adjuster-stop M6-0.75 hex7
10 786-01-3120b 10210 $3.00 adjuster lock nut M6-0.75 x 2 hex7
11 786-01-3120c 00000 $19.0 choke housing M10-1.0
12 786-01-31490 00000 $7.00 choke spring Ø6.5 x 23 stiff
13 786-01-31480 00000 $14.0 choke plunger Ø8 x 17.5
15 786-01-31520 13218 $1.50 clamp nut M5 x 5 hex9
16 786-01-31530 00000 $0.00 clamp screw M5 x 27 slot-hex8
17 786-01-31450 13211 $5.00 idle (both) spring Ø4.8 x 10
18 786-01-31460 00000 $6.00 idle air screw M6-0.75×19, long tip (-1)
19 786-01-31540 13210 $9.00 idle speed screw M6-0.75×17 short tip
20 786-01-31370 00000 $0.00 idle jet 15
21 786-01-31320 00000 $0.00 needle jet E2-137 Ø2.05
22 786-01-31300 00000 --N/A- main jet 45 M5-0.75 small hex
23 786-01-3139a 00000 $0.00 float seat seal washer Ø7 x Ø10
24 786-01-3139b 00000 $0.00 float valve seat M7-0.75 thread hex8
25 786-01-3139c 00000 $0.00 float valve needle
26 786-01-31350 00000 none float
27 786-01-31410 00000 $4.00 float hinge pin Ø2.5 x 23
28 786-01-31360 00000 none float bowl gasket
29 786-01-3100b 00000 none float bowl
30 786-01-31430 10202 $0.70 float bowl screw M4 x 14 phillips
31 786-01-3100c 00000 $0.00 float overflow hose Ø3 x 200
32 786-01-3100d 00000 none clamp sleeve with lip Ø20 x Ø23 x 15.5
34 786-01-3110b 10209 $5.00 adjuster M6-0.75 female x 16 hex7
35 786-01-3110c 00000 $3.00 adjuster lock nut M6-0.75 x 2 hex7
36 786-01-3110d 00000 $0.00 carb top rubber cap
37 786-01-3110e 00000 $0.00 curved pipe cable guide
Angel Carb Service:
1. Angel service p9, 2. page 10, 3. page 11, 4. page 12
4. Mikuni design
A. Pacco
The India-made Pacco P-60 MT carburetor used on 2000-2002 Avanti mopeds
Pacco P-60 MT carburetor, 21 clamp diameter
Left, Dellorto SHA 15/15, same 21 clamp size
Pacco P-60 MT carburetor, 16mm slide parts
.
B. Mikcarb
The India-made Mikcarb is used on 2005 Hero Majestic Pacer. It looks identical to Pacco P-60, except it has a cable choke instead of a flip lever.
Mikcarb on 2005 Hero Majestic Pacer
5. Mikuni Jets
Small Hex used on 1960’s-70’s Yamaha and Kawasaki
045 --N/A- Angel #786-01-31300
050 N/A
060 N/A
070 $3.00
075 --N/A-
080 $3.00
085 $3.00
090 N/A
100 N/A
Small Round used on many Yamaha, Kawasaki, and Suzuki products
060 --N/A-
Indian #E236-00-50
062.5 $8.00 Indian #E236-25-50
065 --N/A- Trac #13206
070 --N/A- Trac #13207
075 --N/A-
080 --N/A-
090 N/A
100 N/A
110 N/A
116 $3.00
118 $3.00
120 $3.00
124 $2.50
132 $2.50
140 $3.00
150 $2.00
155 $2.50
160 $3.00
Large Round used on many Yamaha, Kawasaki, and Suzuki motorcycles
060 --N/A-
062.5 $8.00
065 --N/A-
070 $8.00 Yamaha #620-14231-14-00
075 --N/A-
080 --N/A-
090 N/A
097.5 $2.50
100 $2.50
102.5 $2.50
105 N/A
107.5 $2.50
110 $2.50
112.5 $2.50
115 N/A
117.5 N/A
120 $2.50
122.5 N/A
125 $2.50
127.5 $2.50
130 $2.50
132.5 $2.50
135 N/A
137.5 $2.50
140 $2.50
142.5 $2.50
145 $2.50
147.5 $2.50
150 $2.50
152.5 $2.50
155 $2.50
157.5 $2.50
6. Info
These are the baby Mikuni’s, the smallest of the small, 10 to 13mm for limited 50cc engines. Unlimited 50cc like Kawasaki AR50 or Yamaha YSR50 have 18mm size carburetors. Those are bigger babies, but still “off the charts”.
USA motorcycle parts suppliers commonly have parts for 28 to 44mm Mikuni VM series (classic round slide) carburetors. They have 2.5 or 3.0mm jet needles, not 2.0 like the “babies” have. Their float needles are also bigger.
Yamaha, Suzuki, and Kawasaki supply some parts for the small Mikuni carburetors that are on their 50cc models.
Jet Needle Clips are tiny and get lost easily. The full name of that kind of clip is “metric side-mount external retaining ring (E-style)”. The clip size for moped carburetors is smaller than any motorcycle carburetor clip, because the jet needle and everything else in the carburetor is smaller. A 10mm Indian moped carb jet needle is 2.0mm thick with a 1.5 clip groove. Mikuni carbs 18mm and up have needles 2.5mm thick with a 1.9mm clip grooves, or bigger.
Sources:
- Parts Catalogs provided illustrations, part numbers, descriptions, applications, and some specifications.
- Service Manuals provided most specifications.
- Packaging Labels on some new parts provided part numbers and applications.
- Markings on some used parts provided specifications.
- Direct Measurement on most parts provided specifications.
- Internet Images provided some identification by photo-matching, and occasionally dimensions by photo-scaling.
7. Tillotson HK25A Carb on ’78 Indian AMI-50
Carb kit Rk-32Hk
Tillotson HK25A Carburetor Parts (none)
E210-12-50 Tillotson carb comp. none has no float reservoir
These have an adapter “bell” for the air filter, to interchange with Keihin. These did not work well when they were new with fresh rubber back in 1978. Tillotson carbs were replaced by Keihin, only months after they came out. 40 years later in 2018 their rubber parts, especially the diaphragm, are all stiff. This is the Tillotson carb kit for Indian, Rk-32Hk-4911, available on Amazon.
Tillotson carb, front and back view
Tillotson carb on 1978 Indian