Contents: Avanti Batavus Derbi Motobecane
Contents: Peugeot Puch Sachs Tomos Vespa
Avanti (Garelli VIP remake)
Batavus (Laura M48 engine)
Laura M48 magneto (right) and clutch (left) covers are the same.
Laura, Motobecane, Batavus, Badger, Solo, Angel, Speed Bird magneto covers all interchange, because they all have a 124 mm inner diameter. Here are some original examples:
Here are some examples with the 1980 Motobecane replacement covers installed. For Solo and Tas engines a piece of wire is required, wrapped around engine and the replacement cover tabs.
Above, this one cover fits and replaces all of those covers above. It is exactly for a early 1980’s Motobecane. But it fits anything that takes a 124mm ID round cover. It is deep enough for stock mopeds. But it is not deep enough for some Motobecane CDI magnetos, or any that are much taller than stock. It comes with two rubber clips to hold it onto the metal “ears” on the engine case.
|000.821.5100||1||footrest right||$25||1976-1979 Derbi SL, SLE|
|000.821.5500||2||footrest left||$35||1976-1979 Derbi SL, SLE|
|000.821.5180||chaingaurd left grey||N/A||1976-1979 Derbi SL|
|000.823.0150||9||engine cover right grey||$80||1976-1979 Derbi SL|
|000.823.0200||10||engine cover left grey||$70||1976-1979 Derbi SL|
|000.872.2220||chaingaurd right gold||1976-1979 Derbi SLE|
|000.871.5180||chaingaurd left gold||1976-1979 Derbi SLE|
|000.873.0150||engine cover right gold||N/A||1976-1979 Derbi SLE|
|000.873.0200||11||engine cover left gold||$50||1976-1979 Derbi SLE|
|000.851.5180||TT chaingaurd left black||1976-1986 Derbi TT|
|000.853.0150||12||engine cover right black||$80||1976-1979 Derbi TT|
|000.853.0200||13||engine cover left black||$60||1976-1979 Derbi TT|
|0A0.???.????||14||engine cover L blk used||$50||1984-1986 Derbi SL (no cavity)|
|original only||5||center cover (early non)||N/A||1976-1979 Derbi SL, SLE, TT|
|000.821.8220||6||center cover (non reed)||N/A||1976-1979 Derbi SL, SLE, TT|
|0A0.220.0561||7||center cover (reed)||$90||1980-1986 Derbi SL, SLE, TT|
|000.871.5100||3||footrest right||$35||1986-1989 Derbi Variant Sport|
|continued …||1980-1986 Derbi SL, SLE|
|000.871.5500||4||footrest left||$45||1986-1989 Derbi Variant Sport|
|continued …||1980-1986 Derbi SL, SLE|
|0F0.221.0221||chaingaurd right||N/A||1986-1989 Derbi Variant Sport|
|0F0.152.0181||chaingaurd left||N/A||1986-1989 Derbi Variant Sport|
|000.853.0150||engine cover right||N/A||1986-1989 Derbi Variant Sport|
|000.853.0200||engine cover left||N/A||1986-1989 Derbi Variant Sport|
|0A0.182.0221||8||center cover||N/A||1986-1989 Derbi Variant Sport|
Derbi Center Panels: The center panel choke button is supposed to push the Delorto carburetor choke lever down, and later allow it to release back up after the bike is started and the throttle is momentarily maxed out. But it often does not work properly, and it is finicky. When it sticks, either on or off, you must wiggle or move the center panel to make it click, or else remove the panel and operate the lever directly. The main cause is an incorrect angle of the carburetor. Loosen the clamp and rotate one way or the other. The carb should be vertical, but the finicky panel might require it to be slightly tipped. Because of this difficulty, many Derbi owners have cut holes in, or removed and discarded their center panels. Derbi fixed the problem on the 1986-1989 models by using a choke cable and a right handlebar lever. No more reaching down and fussing.
Derbi Center Panel Choke Button Parts: There are three different “feet” that press onto the vertical plastic button shaft. Here are shown the correct ones, for reference purposes. Some are for sale but not yet listed. Also the steel tongue at the front is for sale but not shown here.
Motobecane 50, 50V (rear suspension)
22249 right MB50 chain guard cover white $35-45
22251 left MB50 chain guard cover white N/A
54318 right MB50 cover white w/gold stripe N/A
54319 left MB50 cover white w/gold stripe N/A
54302 right MB50 chain guard metallic red N/A
54303 left MB50 chain guard metallic red N/A
54304 right MB50 chain guard metallic blue $35-40
54305 left MB50 chain guard metallic blue N/A
00000 right MB50 chain guard misc used $35-40
00000 left MB50 chain guard misc rough N/A
MLM set of polished stainless (like chrome) $80
Cover Screws (coarse thread not regular metric)
A 17424 $5 used original cover screw M5-0.9 x 12 with plastic washer
B 17424 N/A new original cover screw M5-0.9 x 12 bare use E, F or G
B 00000 $6 new original cover screw M6-0.9 x 12 bare
C 00000 $7 new replica cover screw M5-0.9 x 12 bare
D 17425 $3 used belt cover screw xx M5-0.9 x 10 with plastic washer
E 00000 $7 new original screw xxxx M5-0.9 x 12 bare
F 00000 $6 new original screw xxxx M5-0.9 x 10 bare
G 17425 $5 new belt cover screw xxx M5-0.9 x 10 bare
H 00000 $5 new original screw xxxx M6-1.0 x 12 bare
I 00000 $2 new white plastic stepped washer ∅5
I 00000 $3 new white plastic stepped washer ∅6
J 00000 $3 new black plastic stepped washer ∅5
J 00000 $3 new black plastic stepped washer ∅6
K 00000 50¢ new screw for re-thread M5-0.8 x 12 standard
Motobecane 50 Leg Shields
This is an original leg shield set #20250, and mounting bracket set #20290.
It is new but there are some minor scratches, from years of being kept on parts shelves.
These have all sold. Only the lower mount kit is available.
Here is a diagram of some 1950-60’s Motobecane leg shields. The mounts are different.
Motobecane 40 (no rear suspension)
Cover screws are a special thread M5-0.9, not regular M5-0.8.
cover screw 17424 M5-0.9 x 12 rusty $5 rusty
cover screw generic M5-0.9 x 16 phillips $2
cover screw 17426 plastic stepped washer black $3
Motobecane magneto cover black (see above)
Motobecane magneto cover gray used $25- $30 without tabs
Peugeot 103, General and Taiwan clones
All of these models take the same side covers:
L L side cover, used, blue N/A
L1 L toolbox, used, blue $50
L2 L toolbox, used, bluish silver $45
L3 L toolbox, used, bluish silver $45
L4 L toolbox, used, blu-sil, 1 knob $35
R R side cover, new, blue N/A
R1 R toolbox, used, blue, 1 bracket $35
R2 R tool. used blu-sil, no brackets $25
R3 R tool. used blu-sil, no brackets $20
R4 R tool. used blu-sil, no brackets $20
magneto cover Peugeot alum rough $25
Puch Maxi, Newport, Sport
1 410200 side panel set Puch 1-speed black generic $39
2 000000 side panel set Puch 1-sp used black orig xlnt N/A
2 000000 side panel set Puch 1-sp used black rough $30
3 000000 side panel set Puch 2-sp used black rough $60
5 204900 screw M5 x 46 with black knob replica new $3
5 204900 screw M5 x 46 with black knob original used $8
5 204900 screw M5 x 46 with gray knob original used $12
5 000000 screw M5 x 45 phillips head substitute new 50¢
6 000000 left side panel Puch 1-sp used black rough $30
6 000000 left side panel Puch 2-sp used black rough $45
6 000000 left side panel Puch 1-sp used grey rough $55
7 000000 right side panel Puch 2-sp used black rough $45
7 000000 right side panel Puch 1-sp used black rough $25
7 000000 right side panel Puch 1-sp used grey rough $45
8 205100 screw M5 x 36 with black knob replica new $3
8 205100 screw M5 x 36 with black knob original used $8
8 205100 screw M5 x 36 with gray knob original used $12
8 000000 screw M5 x 35 phillips head substitute new 50¢
Right screws: 2 long and 1 short. Left: 1 long and 2 short
All of the Maxi one speed models have the same covers: Maxi, Maxi Luxe, Maxi Sport, Sport, Newport. All of the Maxi two speed models have the same covers: Maxi II, Maxi Sport LS 2, Sport MkII, Newport II.
magneto cover Puch used $20-$40
Puch Rigid, GN, Maxi N
This is the no rear suspension model.
Puch Magnum, Sears Free Spirit, Murray, JC Penney
side panel set Puch Magnum used black original N/A
right side panel Puch Magnum used black original N/A
left side panel Puch Magnum used black original N/A
side panel screw with knob aftermarket M5x15 $3
side panel screw with knob original new M5x15 $6
side panel screw with knob original used M5x15 $3
side panel screw wide slot head subst. M5x15 50¢
Sachs and Hercules
Sachs 504, 505 engines
Left: 0244.067.100 magneto cover for Sachs 505
125.5 mm ID, chrome, good-used $22 or new $26
Right: 0244.167.100 magneto cover for Sachs 504
112.5 mm ID, chrome, new original $22
Hercules or Sachs mopeds
side covers (chain guards) none available
Cover Fasteners (Quarter-Turn Slot-Head)
A 132872 named total
A 132872 length length
A 185818 34.0 43mm $4.00
A 1979-85 Si rear and middle
A 1982-on Bravo (all)
A 1986-on Si (all)
B 132871 00mm 41mm $4.00
B 1977-80 Bravo rear
B 1978-83 Grande rear
B 1979-85 Si front
C 143615 27.5 37mm $4.00
C 1972-80 Ciao rear and middle
C 1980-on Ciao PX rear and middle
D 132872 00mm 33mm $4.00
D 1977-80 Bravo front (can use E, 2mm shorter)
D 1978-83 Grande front, center-front and center-rear
E 143614 23.5 31mm $7.00
E 1972-80 Ciao front (can use D, only 2mm longer)
E 1980-on Ciao PX front
F 122957 spring 34mm $3.00 same for all
67-71 Ciao cover fasteners, different from 72-on
These can be purchased at UK Ebay.
Vespa Ciao Side Covers
1990’s Piaggio Ciao side cover set black $64. Fits ’72-80+ Vespa Ciao.
Includes the chrome emblems but not the fasteners.
Fasteners are front D, middle C, rear C.
Battery Boxes and Covers
Battery boxes were on early 70’s Ciao (US models with brake light), and late 70’s to early 80’s Ciao, Bravo, and Grande “blinker” models (equipped with turn signals and different switches and equipment). These side box covers have been scarce since the late 1980’s. They often fall off, and nobody is reproducing them. If you know of a source please tell Shaun by email.
The larger size box 227 x 160 mm is on Grande. Price $10 per box without lid, good-used.
The smaller box 222 x 158 mm is on Ciao and Bravo. $12 per box without lid, good-used.